WHAT'S NEW!
-
Newest video click here
-
See us in person: EXPO West spot P30 near the Main Gate
May 19-21, Flagstaff, AZ
-
Globe Trekker EXPO merch
-
Please REFRESH pages often


TM
TM
.png)
TM
Click Here

TM
Best DIY Engineered Solutions
Now offering Motorcraft Adventure products!
Arctic Tern Overland distributed here!
EMUK Air-Lift Systems!
TM
TM
TM
TM
TM
TM
Mountain View Adventure Vehicle
All Sub-Frames & Components


All sub-frames come with side brackets, center pivoting crossmembers, and hardware. Sets of side brackets and individual pivoting crossmembers can be purchased separately. Both come with all necessary hardware for installation. Please view the How-To Install a Zero Torsion Sub-Frame video on our Videos page.
TM
3-point Zero Torsion sub-frame
TM

A 3-point subframe consists of two side pivot brackets, normally mounted towards the front) and one crossmember pivot, normally mounted in the rear. The support frame weldment, which is bead blasted, coated twice with epoxy primer, then powder coated for maximum corrosion resistance, and stainless steel hardware are also included.
3-point Zero Torsion sub-frame
TM
8' 3-point - fits 8' rectangle or 10' departure angle
10' 3-point - fits 10' rectangle or 12' departure angle
12' 3-point - fits 12' rectangle or 14' departure angle
14' 3 point - fits 14' rectangle or 16' departure angle
$6428
$6885
$7415
$7955
NOTE: A 3-point subframe is advantageous if you desire a cab to habitat pass through.
3-point or 4-point? Watch this
4-point Zero Torsion sub-frame
TM

A 4-point subframe consists of two side pivot brackets, normally mounted in the middle) and two crossmember pivots, normally mounted in the front and rear. The support frame weldment, which is bead blasted, coated twice with epoxy primer, then powder coated for maximum corrosion resistance, and stainless steel hardware are also included.
4-point Zero Torsion sub-frame
TM
8' 4-point - fits 8' rectangle or 10' departure angle
10' 4-point - fits 10' rectangle or 12' departure angle
12' 4-point - fits 12' rectangle or 14' departure angle
14' 4 point - fits 14' rectangle or 16' departure angle
16' 4-point - fits 16' rectangle or 18' departure angle
18' 4'point - fits 18' rectangle or 20' departure angle
$6428
$6885
$7635
$8175
$8715
$9255
NOTE: A 4-point subframe is advantageous for additional support point loading, and is required for sub-frame length greater than 14'.
NOTE: A 3 / 4-point subframe is available for larger subframes (14' and greater) that need a four point subframe for additional pin pointed loading requirements, but also want to pass through. This subframe allows the habitat to track more closely to the cab of the truck and helps to prevent the pass through boot from dislodging. Add the Heim Joint Kit below for total pricing.
+ $920
Add the 4-point Zero Torsion subframe system above to the current price of the Heim joint kit to determine total price.
TM
4-point Zero Torsion ISO sub-frame


4-point Zero Torsion ISO sub-frame
TM
$850*
The ISO sub-frame, named after the shipping container corner locking mechanisms (ISO 1161), turns your Overland Expedition camper into a daily driver with a Zero Torsion flatbed.
In conjunction with the ISO habitat corner mounts...

...you can attach camper jacks to the mounts and lift your habitat off at your basecamp to roam unencumbered by height and weight.


* Add the ISO corner mounting points to any subframe for an additional $850.
Crossmember Pivot Gusset (pair)
$175

See the Zero Torsion sub-frame in action, keeping this habitat torsion free in an extreme environment... on an Overland Driving course.


Pivots - Zero Torsion ISO sub-frame
TM
Pair of Side Pivot Brackets
One Crossmember Pivot
Heim Joint Set
Crossmember Stiffener Plate
$980
$1340
$920
$45
